White Ensign Models 1/72 Photo-Etched Brass

The table below contains the entire current and forthcoming range of 1/72 etched brass. WORLDWIDE PRICES IN POUNDS (GBP) , and U.S. DOLLARS ($). Click on to the LINKS for a scan of what you get, or for CONTENTS. Please appreciate that size of image does not necessarily correspond to the size of the item you get!

PE 7201 S-100 for the Revell kit.  Supplied as two sheets of brass, of different thicknesses, for extra realism. 5 pages of instructions.

Contains: Rails/Dodgers,  Lifting/locking handle for aft hatch,  Smoke pot handwheels and replacement lifting handles,  Liferaft hand ropes, Compass and sight to replace binnacle tops if required,  Binnacle top window cover and handle,  Replacement rail around top of binnacle,  Windscreen frame,  Replacement bow depression rail,  Aerial insulators x 4,  Cleat for ensign staff,  Tie bars between bridge and antennae supports,  Replacement helmet rack for back of bridge,  Lifting eyes for armoured bridge,  Magazine racks for bow 20mm mounting x 12,  Section of bow 20mm mounting that extends above breech,  Restraining strap/chain for signal platform,  Slatted covers for ventilators,  Extra detail for bridge binocular sight, Torpedo props, fore & aft, Torpedo cradles and hold down straps, Torpedo loading tackle, Bridge compass face (to replace decal), Clear vision screen for forward bridge window, Wheel and engine telegraphs for sad gits that want to detail inside of wheelhouse ;^),  Hinges and handles etc. for front of 37mm shield, 37mm details, Ammunition clip to fit in the clip guide,  Foul weather covers for skylights on top of lockers, Sight for twin 20mm, Valve handwheels x 20
PE 7201 Sheet 1

PE 7201 Sheet 2

STEEL NAVY REVIEW by STEVE BACKER

Take a look at TOM WILSON'S BUILD on ModelWarships.com

PE 7203 TYPE VIIC U-BOAT for the Revell kit.  Contains: 20mm Fittings, Aft Torpedo Loading Hatch, Amidships Deck Hatches, Attack Periscope Mount Footbars, Ballast Tank Vents, Biscay Cross, Bollard Tops, Bow Lower Cable Cutter, Bow Torpedo Tube Doors, Bow Upper Cable Cutter, Cable Tensioners, Compass & Engine Telegraph Dial, Con Tower Top Side Vent Grills, Conning Tower Hatch Mechanism, Conning Tower Markings, Conning Tower Side Vent Grills, Deck Hatch Hinges, Diesel Exhaust, Diving Tank Valve Outlets, Fore Deck Hatches, Forward Torpedo Loading Hatch, FuMo 61 Antenna, FuMo29 Antennas, FuMo30 Radar Antenna, Gun Deck Hatch, Gun Handwheels, Hatch Handles, Large Casing Access Hatch, Naxos Antenna, Periscope Compass Repeater, Periscope Stiffeners, Replacement Rail, Retractable Bollard Plates, Small Stern Access Hatch, Snorkel Housing Crosses, Torpedo Aimer Sight Bezel, Torpedo Aimer Sight Footbars.

PE 7203 Sheet 1

PE 7203 Sheet 2

PE 7205 PT-109/PT-117 for the Revell kit.  Etched in 8 and 5 thou brass.  Contains: 'D' Vents on sides of cabin, .50 cal Gun Mounting Frame, 20mm Depression Rail, 20mm Gun Shield & Fitting Bracket, Foc’sle Foot Rails, Cleats, Chocks, Full Set of 50 cal depression rails shaped to replace the kit parts, Fuel Filler Caps, Hand Rails (Straight), Hand Rails (Curves for Gun Tub Sides), Mast, Rectangular deck hatches, Throttle Quadrant, Torpedo Tube Mounting Feet Assemblies with Trainer Plates, Torpedo Tube Breach Assemblies, Torpedo Tube Training Crank Handles, Torpedo Tube Training Gear Box, 50 Cal Barrel Cooling Jackets, 50 Cal Ammunition Belts, 50 Cal Mounting Cradles and Firing handles, 50 Cal Mounting Pintle, 50 Cal Machine Gun Breach Detail Plates, 20mm Oerlikon Fittings (Ring Sight, Shoulder Braces etc.), Bow Deck Hatch, Chart House Side Windows, Chart House Door Assembly, Coach Roof Hatch, Deadlights (Loads of ‘em), Depth Charge Rack Assembly, Exhaust Muffler Linkages and Butterfly Valves, Instrument Panel, Main Control Panel, Mast Brace, Rubber Boat Paddles, Searchlight Mounting Bracket, Torpedo Control Switch Box, Torpedo Tube Limit Stop Brackets, Windshield Frames.

PE 7205 Sheet 1

PE 7205 Sheet 2

PE 7211 TYPE VIIC U-BOAT TORPEDO LOADING SET for the Revell kit.  Contains: 2 x resin torpedoes, plus photo-etched parts to construct either G7A compressed air or G7E electric powered variants, and photo-etched loading gear as follows:  Sheerlegs Assembly, Torpedo Safety Harness, Loading Cradle Side Stays (Long), Loading Cradle Base, Loading Cradle Side Stays (Short), Loading Cradle Frame, Torpedo Firing Pistol Prop, Torpedo Propellers, Loading Hatch Release Mechanism, G7a Torpedo Tail Fins, G7e Torpedo Tail Fins, Loading Well Deck, Torpedo Nose Cradle, Loading Hatch, Loading Tube (To be Rolled in to Shape), Sheerleg Wire Securing Eye.

PE 7212 KRIEGSMARINE TORPEDO  SET for U-Boat & S-Boat kits.  Contains: 2 x resin torpedoes, plus photo-etched parts to construct either G7A compressed air or G7E electric powered variants.

PE 7213 KRIEGSMARINE 3.7cm SKC30U ON LC-39 MOUNT Contains: Barrel Assembly, Gun Training Mechanism, Gun Mounting and Layer’s Positions, Elevation Mechanism, Sight Elevating Bar, Barrel Restraint for Stowed Gun, Torsion Bars, Gun Layer’s Seat, Training Mechanism Plate, Shoulder Braces, Gun Layer’s Hand Wheels.

PE 7215 KRIEGSMARINE 2cm FLAK ZWILLING Contains: Castings: Gun Barrel Assembly, Shield (Optional), Pintle, Alternative Pintle; Photoetch: Ammo Clip Parts, Shoulder Braces, Hand Wheel, Gun Sight.

PE 7216 37mm U.S. ARMY ANTI-TANK GUN Contains: Castings: Main Gun Carriage, Barrel Assembly, Shield; Photoetch: Gun Breech Plate, Right Shield Mounting, Left Shield Mounting, Towing Eye, Handles, Breech Handle, Shield Top Brace, Elevation Wheel.

PE 7217 USN Mk.3 40mm SINGLE BOFORS Contains: Castings: Pedestal Base, Gun Mounting, 40mm Bofors Gun, Recuperators; Photoetch: Footplate & Frame, Back Railings, Elevation Cranks, Gunsight Yoke, Foot Pedals, Foot Pedal Support Bar, Spent Case Chute, Gun Layers’ Seats.

PE 7221 USN Mk.13 TORPEDOES & ROLL-OFF RACKS Contains: Castings: Torpedoes x 2; Photoetch: Torpedo Support Cradles, Base Thickener, Base Plate, Upper Retaining Latches, Retaining Strap Brackets, Release Handles, Front Beam & Latch Mechanism, Rear Beam & Latch Mechanism, Torpedo Propellers.

PE 7222 USN OLDSMOBILE M4 37mm CANNON Contains: Castings: Pedestal Base, Gun Mounting, 37mm Oldsmobile Cannon, Tripod Centre Spindle; Photoetch: Ammunition Belt,Ammo Feed Front Frame, Ammo Feed Rear Frame, Footplates, Trigger & Hand Grip, Mounting Frame, Mounting Legs, Baseplate.

PE 7232 TYPE VII U-BOAT FLOOD, DRAIN AND VENT HOLES for Revell 1/72 kits.  Contains: 2 different patterns of Cheek Plates,  Main Floods, Torpedo Doors, Saddle Trio Floods, Side Floods, Bow Round Floods (paired & unpaired types), Bow Slots, Side Curved Round Vents, Aerial Tensioners, 2 types of Diesel Exhausts, Conning Tower Side Drilling Templates, S-Geraet, Turnbuckles, Bow Internal Torpedo Braces.

PE 7234 USN 20mm SINGLE OERLIKON Contains: Castings: 20mm Oerlikon Gun, Solid Type Mounting Pintle; Photoetch: Shoulder Braces, Base Ring, Gun Shield, Mounting Legs, Gun Sights, Gun Mounting Bracket, Shield Mounting Bracket.

.

PE 7235 USN 3"/50 DECK GUN Contains: Castings: 3"/50 Gun Barrel, Gun Mounting, Trainers’ Hand Wheels, Sight Elevation Control, Right Hand Foot Step Support, Right Gun Layer’s Handle, Left Gun Layer’s Handle; Photoetch: Elevating Mechanism 2. Cog Doublers, Gun Layers’ Pedals, Sight Adjuster Side Bars, Sights Adjuster, Gunsight Beam, Gun Layers’ Cranks, Left Footplate, Seat Supports, Gun Layers’ Seats, Right Footplate, Securing Stay.

PE 7236 USN 4"/50 DECK GUN Contains: Castings: 4"/50 Gun, Gun Mounting, Elevation Gear, Gun Sight Yoke, Layer’s Seat Frame, Trainer's Mechanism, Sight Yoke Adjuster, Sight Telescopes; Photoetch: Gun Barrel Stay, Base Plate, Left Gun Layer’s Pedals, Right Gun Layer’s Pedals, Layer’s Hand Cranks, Layer’s Seat Spindles, Gun Sight Frame, Gun Layers’ Seats.

PE 7237 USN 5"/25 DECK GUN Contains: Castings: Gun Mounting, 5"/25 Gun, Gun Layers’ Hand Wheels, Counterweight/Sight Yoke, Top Water Shield, Layers’ Crank Mechanisms, Trainer Mechanism Gearbox, Sight Telescopes; Photoetch: Gun Sight Brackets, Gun Sight Stays, Counterweight Brackets, Seat Attachments, Gun Layers’ Hand Cranks, Gun Layers’ Footrests, Gun Layers’ Seats.

PE 7238 USN .50 Cal. AIR-COOLED MACHINE GUN (x2) Contains: Castings: Air-Cooled Gun, Mounting Pintle; Photoetch: Base Plate, Support Braces, Mounting Bracket, *Coolant Pipes, *Gunner’s Handlebars, *Note: not required for this mount).

PE 7239 USN USN Mk.14 21" TORPEDO (x2) Contains: Castings: Torpedo Body x 2; Photoetch: Propellers, Stabiliser Fins.

PE 7240 GATO CLASS SUBMARINE CONNING TOWER DETAILS Contains: Railing Stanchions, Conning Tower Frame Outer Plate, Conning Tower Frame Inner Plate, Upper Shears Frame Rear Brace, Modified Bridge Decking, Lower Periscope Spacer Fillets, Lower Rear Periscope Spacer, Upper Framework Skin Strips, Upper Framework Top Skin Strip, Upper Forward Periscope Spacer, Upper Rear Periscope Spacer, SJ Radar Mast Upper & Lower Braces, SJ Radar Mast Top Mounting, Lower Forward Periscope Spacer, Upper Framework Forward Side Fillets, SJ Radar Mast Center Brace, Alternate Upper Framework Rear Brace, Upper Framework Rear Side Fillets, Upper Framework Top Former, Upper Framework Lower Former, Upper Framework Centre Former, Lower Framework Fore & Aft Beams, Lower Framework Center Beam, Lower Main Frames. NOTE: 215mm OF 3.5mm THIN WALL BRASS TUBE (INTERNAL SIZE) AND TWO SMALL LENGTHS OF 0.040” PLASTIC STRIP WILL ALSO BE REQUIRED. The brass tube can be purchased as White Ensign Models part number WEM Z 08.

PE 7241 GATO CLASS SUBMARINE RADARS & ANTENNAS Contains: DBU Antenna (Point Top), DBU Antenna (Flat Top), SV Radar Antenna Assembly, SD Radar Antenna (Early), SD Radar Antenna (Late), SJ Radar Antenna Assembly (Early), Wire Antenna Spreaders, SS Radar Antenna Assembly, Rectangular DF Antenna Front Panel,  Rectangular DF Antenna Plates, Rectangular DF Antenna Mounting Frame, SJ-1 Radar Antenna Assembly (Late).

PE 7242 GATO CLASS SUBMARINE PROP GUARDS & STERN DETAILS Contains: Port Propeller Guard, Starboard Propeller Guard, Center Frame, Aft Frame, Forward Frame, Center Frame Braces, Fore and Aft Beam, Beam and Frame Stiffeners, Side Securing Buckles, Top Forward Securing Buckle, Top Aft Securing Buckle.

PE 7243 USN .50 Cal. WATERCOOLED MACHINE GUN (x2) Contains: Castings: Water-Cooled Gun, Mounting Pintle, Coolant Box; Photoetch: Base Plate, Support Braces, Mounting Bracket, Coolant Pipes, Gunner’s Handlebars.